OP
OP
johnboscoville

johnboscoville

Administrator
Staff member
It rests but still the same issue.
If your mifi falls in this category M028T/M023T [L02CL02C17XX] then the above method should work fine. You can try the process again and see if it works. Just follow the steps carefully.
 

Ipyana93

Leecher
Hello,

AM new here, but I have followed all the steps but I got to stuck at Installation of LTE_MIFI_Generic_Driver since there are installation pictures missing from the link but I have tried to install and it Says "Software device Installed but may not work correctly. This device can not start. (code10)".

Thank you for your consideration
 
OP
OP
johnboscoville

johnboscoville

Administrator
Staff member
Hello,

AM new here, but I have followed all the steps but I got to stuck at Installation of LTE_MIFI_Generic_Driver since there are installation pictures missing from the link but I have tried to install and it Says "Software device Installed but may not work correctly. This device can not start. (code10)".

Thank you for your consideration
Sorry for the inconveniences, you should try and see if you can get the generic driver to install correctly else I doubt if the rest process will work fine.
 

GHostPro

Leecher
This method works on about 60% new m028T with board serial L02C17XXXX-XXX. This method has been adopted due to unavailable firmware's to solve FBF error. Not all L02C17xxx gives such error and so users should take note.
It works greats on most 3g networks and some 4g network. However, there exist limitations in 4g/LTE BANDS


MORE ABOUT NTIM AND OBMI (boot files of DEVICE)

WARNING
You should know what you are up to; don't mess with file size during editing




MORE ABOUT FBF VERSION AND RELATED SOLUTION

NTIM and OBM
On bootup, the Boot ROM loads the OBM from storage memory to internal SRAM and hands control to it. The OBM reads the content of the Non-Trusted Image Module (NTIM) and searches for a DDR configuration package. If one exists, the OBM uses the information in the NTIM to configure the MCU. The NTIM can be customized for specific DDR devices by changing the register values. The sequence in which these registers are arranged in the NTIM description file is the same sequence in which these registers are programmed by OBM. The following is an example section of the NTIM Descriptor file that relates to DDR configuration.

NTIM binary can be generated from the NTIM description file using the latest WTPTP release package available on the Marvell extranet at:
My Products/Cellular & Handheld Solutions/Applications Processors/ARMADA 16x (ARMADA 16x - 88AP16X)/Software > WTPTP
Alternatively, an existing NTIM binary can be modified using a hex editor. Figure 3: "Example DDR Package within the NTIM Binary File" shows the DDR information in the NTIM binary. Starting at address 0x110 (in Figure 3) is a list of ID/value MCU
register pairs. For convenience, the registers IDs are shown on the right side of Figure 3.
Ensure the file size is not altered if editing the binary NTIM file.




CHECKS
• The dashboard must have 3g, 4g only, 4g/LTE and auto mode in other to function
• Dashboard with 4g only is likely NOT supported. I have tested on 4g only dashboards doesn’t seem to work
It works on L02C16XXX



WARNING
1. This method creates dashboard instability
2. Login data somehow not maintained and some users will have persistent login problems


SOLUTION
If wireless login problem persists; try login with USB cable; “admin” or default password and modify wireless settings manually

REQUIREMENTS
1. WTPTP DRIVERS
2. LTE GENERIC MIFI DRIVERS
3. MIFITOOL



GUIDE

1. Files Needed

View attachment 371

2. Install WTPTP Driver

View attachment 379

3. Install LTE Generic driver see tut here


4. Run Mifitool

View attachment 372

5.

View attachment 373

6.

View attachment 375

7.

View attachment 376

8.

View attachment 377

9.

View attachment 378

10.
Insert battery non-default sim card and battery, power on the device and insert USB cable

Log in to the dashboard using "admin" or default login password

Locate Network Mode and set to Auto

Network Displayed

Unlock Done

You do not have permission to view link Log in or register now.


Credit to Droid Peeps and His team for this great Tut.
Extended, modified, and tested by GHCorner.com
Pls can anyone having the downloaded files send it to my mail [email protected] cus I cnt download it from the link it says the file is corrupt
 

Important Notice


We do not support the downloaded files and how to run content

LIKE OUR FACEBOOK PAGE

Top